radius arm idea

Post Reply

Topic author
Mark C.
I get chills without my van.
Posts: 60
Joined: Mon Oct 29, 2012 3:35 pm

radius arm idea

Post by Mark C. »

I have a suggestion for those researching a SAS. I have SAS'ed a few toyota's in my time and at one point I looked into ways of doin it to a 4runner that was my daily driver,so I really didn't want much lift. I searched and decided on radius arms,not just any radius arms,Land Rover radius arms. These arms have bushings fore and aft instead of top and bottom,with the arm connection under the axle forming a skid/axle protector. This bushing configuration leaves the top of the axle clear and unobstructed for clearance,coils,shocks,with nothing to hit frame rails or anything. A SAS would be possible without going a mile high. The Land Rover Discovery arms use standard shackle style bushings at the axle and a standard Ford style pin bushing at the frame,they are long enough to get good travel and are cheap at junk yards. I think its worth considering and would love to see it. If you are still in the "gathering info stage" find a "disco" and check out the front end. These arms could be mated to any axle.

LiftedAWDAstro
I have my van tatooed on my cheeks
Posts: 4379
Joined: Sat Sep 09, 2006 3:35 pm
Location: New Haven, NY

Re: radius arm idea

Post by LiftedAWDAstro »

Good info to have, thanks.
Current rides:
2013 Toyota Tundra DC 4x4
2008 Dodge Nitro 4x4
2005 Nissan Sentra 1.8S Special Edition

Mileage spreadsheet

Vans owned:
1986 Safari 2.5L 4 speed manual - scrapped
1995 Astro 2WD conversion 4.11 posi, shift kit, DHC rock rails - sold to Skippy
1998 Astro 4x4 D44, D60, NP231, full hydraulic system with 9k# Milemarker winch and snow plow - sold to Lockdoc
2003 Astro AWD all stock - traded for a 3/4 ton truck
2005 AWD, 4.10's - sold to skippy

Cobra
ASV Supporter
ASV Supporter
Posts: 1750
Joined: Sat Jun 16, 2007 2:31 pm
Location: Toronto, Ontario
Been thanked: 1 time

Re: radius arm idea

Post by Cobra »

i was thinking about radius arms lately this is interesting to look into any years in particular?.
1998 GMC Safari AWD, BFGoodrich AllTerrain T/A
Jet performance tuner 91 octane preset, Jet under-drive pulleys
Rancho 999000 series shock, on-board controller to be installed later
DHC rock rails and skid plate Add-A-Leaf
G3500 front calipers
Zexel Torsen Diff
11" drums
180 amp Alternator
Long tru-cool 4590 trans cooler

1997 gone

Cobra
ASV Supporter
ASV Supporter
Posts: 1750
Joined: Sat Jun 16, 2007 2:31 pm
Location: Toronto, Ontario
Been thanked: 1 time

Re: radius arm idea

Post by Cobra »

since i can't edit my post...
i was investigating these more and found the 1989-1998 discovery's use the ford style chassis mount and those seem to be the preferred mount. The new Mercedes-Benz G63 uses the same style arms and mounts on the civilian and military spec vehicles very interesting indeed :-k
1998 GMC Safari AWD, BFGoodrich AllTerrain T/A
Jet performance tuner 91 octane preset, Jet under-drive pulleys
Rancho 999000 series shock, on-board controller to be installed later
DHC rock rails and skid plate Add-A-Leaf
G3500 front calipers
Zexel Torsen Diff
11" drums
180 amp Alternator
Long tru-cool 4590 trans cooler

1997 gone

sonic reducer
I am merely driving my van
I am merely driving my van
Posts: 7
Joined: Tue May 08, 2012 10:20 pm
Location: Seattle wa

Re: radius arm idea

Post by sonic reducer »

What I'd use is toyota fj80. The component are better than land rover :vom: and the axles themselves are strong and wide enough for an astro.
I had amassed a bunch of fj80 junk for a Tacoma I had but never made it happen.
The radius arms are perfect for a streetable 4x4 that doesn't need mad flex but needs to handle and ride well on solid axles. Almost as easy as leafs too!
User avatar

mdmead
ASV Supporter
ASV Supporter
Posts: 2153
Joined: Sun Sep 10, 2006 6:45 pm
Location: Selah, WA
Been thanked: 1 time
Contact:

Re: radius arm idea

Post by mdmead »

One of the cleanest and most stock-like 4x4 conversions I have ever seen done to an Astro/Safari was using the complete frontend out of a mid-to-late 70s Ford 1/2 ton 4x4. Correct width Dana 44 solid axle, coils and radius arms. If I ever decided to put a solid axle under mine, this is the way I would go.
Matt
Selah, WA
-96 GMC Safari AWD Hi-Top Conversion -->Stalled 5.3L swap & 5" lift
-74 Ford Bronco -->Far from perfect but mine!
-99 V-10 Ford Super Duty Super Cab 4x4 -->Stock with 285 Cooper ATs
-00 Ford Focus Wagon -->The Red Turd
-95 Ford 24' Class C Motorhome -->My big block sleeper
-07 Can-Am Outlander XT -->My yellow 4x4 quad for work & play
-04 Ski Doo REV Summit -->Still several chassis behind!


No new projects until the current ones are done!
Post Reply